She has also been identified as a pioneer in early flip chip technology.

Individual points and money (known as Flip Chips) are also shown here.

Soon after, the company added flip chip assembly and die-attach equipment to its repertoire of resources.

Alternatively, with a flip chip technology, solder bumps are used to join stacked chips together.

Today, flip chip is a well established technology and collapsed soft solder connections are used in the vast majority of assemblies.

Processing a flip chip is similar to conventional IC fabrication, with a few additional steps.

Flip chips have several disadvantages.

During that decade, however, the industry was forced to find new techniques when it developed sophisticated methods for packaging chips, known as "flip chip" modules.

Flip chips have recently gained popularity among manufacturers of cell phones, pagers and other small electronics where the size savings are valuable.

Possibilities to contact to pads include soldering, wirebonding, Flip chip mounting, or probe needles.

Flip chip, or controlled collapse chip connection (C4)

Figure 2 is a photo of EN plated bumps on a flip chip, something impossible to accomplish with an electroplated deposit.

In a technique called flip chip, digital integrated circuit dies are inverted and soldered to a module carrier, for assembly into large systems.

Flip chip packaging allows far better cooling of the die by flipping it and exposing it directly to the cooling solution.

DEC continued to hold the flip chip trademark until June 6, 1987, when the trademark was allowed to expire.

It is packaged in a 1,085-pad flip chip alumina ceramic land grid array (LGA).

Flip chip - The concept is similar to flip-chip in package configuration widely used in the silicon integrated circuit industry.

As can be seen in the photo, boards containing flip chip modules were etched and drilled to allow those modules to be replaced by discrete components.

An upgrade to the Flip Chip led to the R series, which in turn led to the PDP-7A in 1965.

To attach the flip chip into a circuit, the chip is inverted to bring the solder dots down onto connectors on the underlying electronics or circuit board.

The company also states to have qualified solder bump versions of the same two chipsets to be used for flip chip mounting, the preferred assembly technology in high-volume production.

The core businesses of Finetech are in the fields of precision component placement, flip chip and optoelectronic bonding, and SMT rework.

Around this time, Delco sought to commercialize its technology and formed Flip Chip Technologies with Kulicke & Soffa as a partner.

In 1964 DEC introduced its new Flip Chip module design, and used it to re-implement the PDP-4 as the PDP-7.

The package supplies currents to the pads of the power grid either by means of package leads in wire-bond chips or through C4 bump arrays in flip chip technology.

The technology underpins the whole of electronics and is rapidly developing in new areas such as "flip-chip".

Flip chip - The concept is similar to flip-chip in package configuration widely used in the silicon integrated circuit industry.

The same circuits were then packaged as the first "R" (red) series "Flip-Chip" modules.

Flip-chip is a technique, using minute solder balls to attach ICs both physically and electrically to a substrate.

Such an approach is analogous to the use of conventional, flexible PCBs with the advantage of flip-chip and bare die attachments.

Controlled Collapse Chip Connection - (C4) See Flip-Chip.

Its low pin count configuration and compact form factor – 0.172mm(2) active silicon area per lane – makes it suitable for a variety of flip-chip and wire-bond packages.

Design and testing of a kinematic package supporting a 32x32 array of GaAs MQWs flip-chip bonded to a CMOA chip.

When DEC began to use monolithic integrated circuits, they continued to refer to their circuit boards as "Flip-Chip" modules, despite the fact that actual flip chip mounting was not used.

IPD shipments by packaging platform (WLP, Wire bond, Flip-chip, Embedded, Silicon submount, 3D TSV interposer, Fan-Out plastic laminate...)

Various manuals produced by DEC refer to the modules as "FLIP CHIP", "FLIP-CHIP", "Flip Chip", and "Flip-Chip", with trademark and registered trademark symbols.