hose clip
hose clamp
jubilee clip trademark

The return pipes are low pressure and can be held using normal hose clips.

"We showed them how to eliminate some hose clips and save money.

About 30 seconds later the 2cm spring-loaded hose clip flew into his left eye.

Optional 4-point braces with a hose clip are also available for the harness.

The hose clip is not used at the handle with the extension handle.

During and after the war other hose clip manufacturers started to emerge all over Europe, but Jubilee continued to be successful.

This must have involved removing the intercooler pipe as it had already been fitted with two replacement hose clips.

The design has been copied with many variations, and there are many other hose clips of a similar design.

A flexible outlet pipe designed to accept 25mm or 32mm pipework is supplied with a hose clip for simple connection.

Fix the pneumatic hose to the steel tube from the fan with a hose clip.

Push on hose and use a hose clip to hold hose on.

ABA hose clips were also added in 1982, as a key element in the pipe and pipe-fitting programme.

"The leak was the result of damage a hose clip sustained during the launch," said Don A. Cameron, president of the company.

Tubing should be secured by crimped clip or similar hose clip (not wormdriven) and be gas tight.

As with all our products, our Hose Clips are the best quality available, and are 100% Stainless Steel.

Please note, we cannot grind th einside of hex bolts, Socket Caps or hose clips, only brighten them.

The use of worm-drive hose clips or Jubilee clips is specifically forbidden in the UK and other countries.

Whatever your hose clip needs, TOOLBANK has it covered.

A hose clamp or hose clip is a device used to attach and seal a hose onto a fitting such as a barb or nipple.

Teflon tube extensions are pushed through the bulkhead and the line connection is finished by attaching a small hose clip to the base of the Teflon tube extension.

Gas-tight connections between the flexible hoses and rigid fittings are made by using crimped hose clips or ferrules, often referred to as 'O' clips, over barbed spigots.

Hose clips and Pipe clamps are included in our Fasteners section, but items such as cable ties, wire-tidies and simple press-fitting fasteners have since helped increase the range.

Propane gas is highly flammable (to state the obvious) - do yourself a favour and buy a proper length of gas hose and hose clips, its the best money you will spend.

HI-GRIP STAINLESS hose clips have fast become the industry standard for marine applications throughout the world due to their high quality and performance.

A full range of stainless steel hose clips,top grade Samco high temperature silicone vacuum/boost hose and a variety of plastic T-pieces,unions and adapters are always held in stock.

Jubilee Clips are available in a range of sizes (diameters).

Then slide the eyepiece in and out of the jubilee clip until the image comes into sharp focus.

A jubilee clip tightened round the boss may help.

Fit lots of jubilee clips and tighten it all up. Viola!

Several of the jubilee clips are a 6mm nut with a slot for a screwdriver.

Aluminium housing fits in a radiator hose with jubilee clips.

He'd seen clearly that the jubilee clip was cutting into the rubber joint and if it cut too far .

We covered the crack at the top with muffler bandage and the our good old piece of tin held in place by Jubilee clips.

The hose was then secured with jubilee clips and the provided instructions for tuning the device were followed.

The company owns the trademark for Jubilee Clip.

With the two parts of the nozzle firmly attached by a Jubilee clip to the motor, the blower is ready for action.

The new Viper filter was screwed into place and all the relevant jubilee clips were retightened.

For a start the jubilee clip holding the inter carb fuel line fouled the choke.

A Jubilee Clip is a circular metal band or strip combined with a worm gear fixed to one end.

Larger-diameter Jubilee Clips tend to have wider bands.

Slide the eyepiece into the drawtube until the jubilee clip touches the neck of the drawtube.

Jubilee Clips are generally made of stainless steel or galvanised or electro-plated steel.

Jubilee Clip The following extract from a 4,000 word transcript illustrates how Symbolic Modelling works in practice.

The use of worm-drive hose clips or Jubilee clips is specifically forbidden in the UK and other countries.

Pat started working for Jubilee Clips in Gilingham before going to work with Aylesford Sewage works.

Fit the mount to a clean dry carb and inlet manifold ends, use the wide type jubilee clips, don't over tighten it will split the rubber!

I undid the jubilee clips and yanked the old hose off, marvelled at how much oil was inside, and stuffed the dump valve hose on.

If the brake servo hose internal diameter is too small (i.e. narrow gauge) then sleeve it with 9.5mm fuel/emission hose and four jubilee clips.

Now take two jubilee clips for each can, and attach to the exhaust pipes under the car, keeping the cans as far apart from each other as possible.